THE PERSONAL BREW BENCH

AeroPress Ratio Experiment

Run a simple AeroPress ratio experiment: fix your dose, change the water, log each brew and taste the difference so you find a coffee-to-water ratio you like.

5 min read7 viewsAeroPress Ratio Experiment
— · 0 votes
Contents
  1. Why change the ratio before anything else
  2. Setting up the dose and the scale
  3. Choosing the ratios to compare
  4. Running the brews in sequence
  5. AeroPress Ratio Questions
  6. How do I start an AeroPress ratio experiment?
  7. Is the AeroPress good for ratio testing?
  8. How much water should I change between brews?
  9. What should I write in a brew log?
  10. Does the steep time count as part of the ratio?

An AeroPress ratio experiment changes one number at a time, the coffee-to-water ratio, and keeps every other step the same so you can taste what the change did. You weigh a dose, pick a brew ratio, and adjust the water weight across a few brews. A short brew log then shows which ratio you want to repeat.

  • Change only the water weight between brews and hold the dose, grind and steep time steady.
  • Weigh coffee and water on a scale so each ratio is something you can repeat.
  • Taste each cup and write a note in a brew log before you change anything else.
  • Compare a narrow range of ratios first, then refine the one that suits your coffee.

Why change the ratio before anything else

The brew ratio is the weight of water compared with the weight of coffee, and it shifts strength and flavor together. Adjusting the ratio is the cleanest single change in an AeroPress because you can weigh both sides of it. Dose, grind and steep time stay put while the water weight moves.

A fixed dose and a fixed steep time make each cup comparable to the last one. When two brews differ only in water weight, the taste difference belongs to the ratio. That is the point of an AeroPress ratio experiment rather than changing several settings at once.

Start from the ratio you already brew and treat it as the reference cup. A coffee-to-water ratio written as 1 to 15 means one part coffee to fifteen parts water by weight. Note your reference ratio in a brew log so later cups have something to answer to.

Setting up the dose and the scale

Weighing the dose is the first step of any ratio test on an AeroPress. A digital scale reading to a single gram keeps the coffee side of the ratio stable across brews. Choose a dose that fits your brewer and your mug, then keep it identical every time.

Water weight is the number you will move, and the scale should read it as you pour. Place the brewer on the scale and add water until the display reaches your target. A few grams of water stay in the coffee bed, so treat the poured weight as the working number.

Record the dose and the water weight in grams beside each other in your brew log. Grams make the arithmetic simple: a 15 gram dose at 1 to 16 calls for 240 grams of water. Write the ratio down as a pair so you can rebuild it later without guessing.

Choosing the ratios to compare

A ratio experiment works by comparing a small spread of water weights around your reference cup. Move in steps of about one part water, such as 1 to 14, 1 to 15 and 1 to 16. Close steps keep the flavors related, so you can hear what the water is doing.

Lower water weight, meaning a stronger ratio, brings the coffee forward and can sharpen acidity. Higher water weight, a longer ratio, lightens the body and stretches the finish. Neither direction is better on its own; the coffee and your taste decide it.

Keep the grind, water temperature and steep time the same during the first round. Taste the brew before deciding what to try next. If two adjacent ratios taste alike, widen the gap on the following round.

Running the brews in sequence

Run the brews one after another in a single sitting so your palate stays with the coffee. Rinse the brewer between cups and keep the water at the same temperature each time. Fresh grounds from the same bag anchor the comparison.

Weigh the dose, pour the water to the target weight, and hold the steep time you set for the experiment. Press the same way for every cup so the plunge does not become a second variable. Note the numbers in your brew log straight away.

Label each cup with its water weight so you do not mix them up on the counter. Sip them side by side and give each cup a moment to cool a little. Cooling often reveals sweetness or a dry finish that the first hot sip hid.

AeroPress Ratio Questions

How do I start an AeroPress ratio experiment?

Start with the dose, water weight and steep time you already brew and call that cup the reference. Then change only the water weight in small steps across a few brews. A brew log of each cup lets you compare them without relying on memory.

Is the AeroPress good for ratio testing?

Yes, the AeroPress is a practical brewer for ratio tests because you control the water weight directly. You pour a measured amount onto a weighed dose and time the steep yourself. Those controls make the water weight the only thing you need to move between cups.

How much water should I change between brews?

Change the water in steps of about one part water against your coffee dose. A jump from 1 to 15 to 1 to 16 is a small, readable change. If neighboring cups taste the same, widen the step on the next round.

What should I write in a brew log?

A useful AeroPress brew log holds the dose in grams, the water weight in grams, the grind setting and the steep time. Add a short taste note for each cup. Those four numbers let you rebuild any cup and understand the effect of the water.

Does the steep time count as part of the ratio?

No, steep time is separate from the ratio, and you should hold it steady during a ratio test. The ratio compares coffee weight with water weight only. Changing the steep at the same time muddles what the water change did.

Read next

Latest articles