# Coffee Strength Ratio and Measurement Basics

Learn how coffee strength is measured, what strength numbers mean, how brew ratio shapes the cup, and how to set a medium strength coffee ratio.

Coffee strength describes how much dissolved coffee material sits in your cup, and it is measured as total dissolved solids, or TDS. Strength is different from how much flavor you extract from the grounds. Brew ratio, the weight of coffee to the weight of water, is the lever you control to aim for a target strength. 

- Coffee strength is the concentration of dissolved coffee material in the liquid, expressed as TDS.
- Brew ratio sets how much water passes through each unit of coffee, which shifts strength.
- A tighter ratio, less water per gram of coffee, raises strength and a looser ratio lowers it.
- Strength scales on packaging and machines refer to different things, so check what the number counts.
- Taste is the final check, because a target TDS number alone does not promise a good cup.
 

## What coffee strength actually means 

Coffee strength is the concentration of dissolved coffee solids in the brewed liquid. Baristas express it as total dissolved solids, or TDS, a percentage of the cup's weight made of coffee material. A higher TDS means a denser, heavier-tasting liquid and a lower TDS means a thinner one. 

Strength is not the same as extraction, though the two travel together. Extraction is how much of the soluble material the water pulls from the grounds overall. A cup can be strongly concentrated yet under-extracted, or dilute yet over-extracted, so read the two measures separately. 

The roast and the grind change what lands in the cup as well. A darker roast dissolves more readily and can raise concentration at the same ratio. A finer grind exposes more surface and speeds the release of soluble material into the water. 

## How coffee strength is measured 

Coffee strength is measured by testing a small cooled sample of the brew for its dissolved solids. The reading comes out as a percentage of the liquid's weight, which is the TDS figure. Refractometers do this job, and they need careful calibration and a clean sample to read well. 

A reading taken by hand is only as good as the sample and the device. Cooling the brew, stirring it and filtering out grit keeps the light path clear. Repeat the reading a couple of times and treat a small disagreement between results as noise, not as a new recipe. 

You can also judge strength without an instrument by tasting and feeling the liquid. Body, weight on the tongue and how quickly the flavor fades all point to concentration. Those impressions are useful, though they cannot give you a number to log. 

## Reading the strength numbers you see 

What [coffee strength numbers](/articles/coffee-strength-chart/) mean depends on where the number is printed. A TDS percentage from a refractometer describes dissolved solids in the liquid. A number on a bag or a machine often describes a roast level, a brew style or a setting of the device, not a measured concentration. 

Strength scales on consumer equipment are relative labels made by the maker. Two machines can use the same word for different concentrations, so compare results by taste rather than by label. A TDS percentage is the figure you can compare across brews, because it has a fixed definition. 

When you record a brew, write down the measure you used next to the number. Noting 'TDS percentage' or 'machine setting' keeps your notes honest. A figure without its method tells you little when you return to it later. 

## Brew ratio is your strength control 

Brew ratio is the weight of coffee compared with the weight of water, and it is the main control over strength before you taste. A tighter ratio uses less water for each gram of coffee and pushes concentration up. A looser ratio adds water and brings concentration down. 

Weigh both the grounds and the water so the ratio stays repeatable. A scale removes the guesswork that scoops and marks on a carafe leave behind. Write the ratio as coffee first and water second, so a note reads the same way every time. 

Changing the ratio moves strength more reliably than changing the grind. Grind shifts extraction and can change strength as a side effect. Adjust the ratio when the cup needs more or less weight, then refine the grind for flavor balance. 

## Setting a medium strength coffee ratio 

A medium strength coffee ratio sits between a dense, syrupy brew and a light, tea-like one. The exact figure depends on your brewer, your grind and the roast, so treat any starting point as a place to begin. Adjust from there by taste and by a TDS reading if you have one. 

Start with a moderate ratio, brew a full cup and taste it before changing anything. If the cup feels thin, tighten the ratio by adding a little coffee or removing water. If it feels heavy and muddled, loosen the ratio with more water and taste again. 

Keep one variable fixed per test so you learn what each change does. Record the ratio, the grind and the result in the same note. A short log of changes turns a vague sense of strength into a recipe you can repeat. 

- Weigh the coffee and the water on the same scale.
- Choose a moderate starting ratio and brew it fully.
- Taste and note body and how long the flavor lingers.
- Tighten the ratio if the cup tastes thin.
- Loosen the ratio if the cup tastes heavy or muddled.
- Change one variable at a time and record the result.
 

## Why strength and extraction differ 

Extraction describes how much soluble material the water removed from the grounds, while strength describes how concentrated the result is. The two measures answer different questions about the same brew. Confusing them leads to chasing the wrong adjustment. 

A brew can extract heavily and still taste weak if too much water went through the grounds. Conversely, a small, strong cup can taste sharp because it was extracted poorly. Extraction quality shows up in flavor, and concentration shows up in weight and density. 

Judge extraction by sweetness, acidity and bitterness in balance. Judge strength by body and intensity. When both need work, fix extraction first with the grind, then set strength with the ratio. 

## Keeping a strength record that helps 

A useful strength record holds the ratio, the grind setting, the water and the measure you used. Add a short tasting note beside the numbers. The note explains why a brew worked, which a bare figure cannot do. 

Log the TDS percentage when you measure it, and log the machine setting when you do not. Mark which one you used so later entries stay comparable. Small changes made one at a time show their effect clearly in the log. 

Review the record before your next brew and pick a single change to test. Repeating a good ratio builds the habit that makes the ritual steady. The record turns strength from a guess into a decision. 

## Coffee Strength Questions Answered 

### What is a coffee strength ratio? 

A coffee strength ratio is the relation between the concentration you want in the cup and the brew ratio that produces it. The brew ratio, coffee weight against water weight, is what you actually set at the scale. Strength then follows from that ratio, the grind and the roast. 

### How is coffee strength measured? 

Coffee strength is measured as total dissolved solids, a percentage of the liquid's weight, typically with a refractometer on a cooled, filtered sample. Careful calibration and a clean sample keep the reading trustworthy. Tasting for body and weight gives a useful check alongside the number. 

### What do coffee strength numbers mean? 

A TDS percentage describes dissolved coffee material in the liquid, and that figure has a fixed definition. Numbers on bags and machines often describe roast level, brew style or a device setting instead. Note which kind of number you are reading before you compare it with another. 

### What is a medium strength coffee ratio? 

A medium strength coffee ratio is one that lands between a dense, syrupy cup and a light, tea-like one. The exact figure depends on your brewer, grind and roast, so begin at a moderate ratio and adjust by taste. Tighten it if the cup feels thin and loosen it if the cup feels heavy.
