THE PERSONAL BREW BENCH

Coffee Grind Size Chart: Matching Grind to Brewing Method and Extraction

A practical coffee grind size chart from finest to coarsest, how grinding methods differ, and how to adjust grind to your brewing method. Unverified details are flagged.

4 min readThe ratio desk8 viewsCoffee Grind Size Chart: Matching Grind to Brewing Method and Extraction
— · 0 votes
Contents
  1. What a coffee grind size chart is for
  2. Grind size chart by brewing method
  3. Pour-over grind size
  4. Grinding methods and what each produces
  5. Steps: choosing and adjusting your grind
  6. How to judge the result
  7. Safety

What a coffee grind size chart is for

A grind size chart matches how finely coffee is ground to the brewing method you plan to use. Grind fineness strongly affects brewing because it changes how much of the coffee's surface is exposed to water. As a general rule, methods that keep grounds in contact with hot water for longer call for a coarser grind, and faster methods call for a finer grind. Use a chart whenever you change brewing methods, buy pre-ground coffee, or set up a new grinder.

Grind types are often named after the brewing method they suit. Turkish grind is the finest. Grinds for a percolator or French press are the coarsest. Most common grinds fall between these extremes, and a medium grind suits most home drip coffee machines.

Grind size chart by brewing method

Grind | Typical brewing method | Relative contact time
Finest (Turkish) | Turkish coffee | Grounds stay in the drink
Fine | Espresso | Short, under pressure
Medium | Most home drip coffee machines | Moderate
Coarse | French press, percolator | Long

This chart is qualitative. The supplied evidence does not give particle sizes in microns or numbered settings for any grinder, so none are listed here. Numbered grind charts are specific to each grinder model; for Breville or Sage machines, or for a coffee shop's grind labels such as Starbucks, rely on that manufacturer's or retailer's own documentation. A printable PDF chart is likewise not available from the supplied material.

Pour-over grind size

Pour-over is a drip filtration method, so the medium range is the natural starting point. The supplied evidence describes medium grind for common home drip machines but does not specify a separate pour-over setting. Start at medium and adjust using the steps below.

Grinding methods and what each produces

Burr grinding: Revolving burrs crush and cut the beans between them, either in a manual or an electric grinder. Burr grinders produce a more uniform grind than blade grinders, and their adjustable setting lets you move along the chart in controlled steps.

Chopping: Blade grinders cut the beans with spinning blades. The result is uneven, and fineness depends on how long the grinder runs rather than on a fixed setting. Blade grinders can also create fine coffee dust that may clog the filters of espresso machines and French presses.

Pounding: A mortar and pestle can pound coffee very finely. This is a traditional way to reach the finest grind used for Turkish coffee.

Roller grinding: Industrial grinders pass beans between pairs of corrugated rollers. This produces an even grind and is used commercially rather than at home.

Steps: choosing and adjusting your grind

  • 1. Identify your brewing method and how long the water stays in contact with the grounds.
  • 2. Pick the matching grind from the chart: finer for short contact or espresso, coarser for long steeping such as French press.
  • 3. Choose a grinding method. A burr grinder gives the most uniform result and repeatable settings. With a blade grinder, run it in short bursts and check the grounds, since fineness depends on run time. For Turkish coffee, a mortar and pestle can reach the very fine grind required.
  • 4. Brew with your usual method.
  • 5. Judge the result, then change one thing at a time. If the brew seems over-extracted for your taste, go coarser. If it seems under-extracted, go finer. Keep other variables the same so the effect of the grind change is clear.

Change course if your filter clogs or drains poorly. That often points to too many fine particles, either from grinding too finely for the method or from the dust a blade grinder produces. Grinding coarser or switching to a burr grinder addresses both causes.

How to judge the result

  • Uniformity: Look at the grounds. Particles of similar size indicate an even grind; a mix of chunks and powder indicates uneven grinding, typical of blade chopping.
  • Fine dust: Visible powder in the grounds, or sediment that clogs a French press mesh or espresso filter, signals too many fines.
  • Match to method: Compare the grounds against the chart. Turkish should be the finest, and French press or percolator grounds should be noticeably coarse.

Gaps in the evidence: The supplied material does not provide verified taste descriptors for under- or over-extraction, target brew times, water temperatures, coffee-to-water ratios, or numeric extraction targets. Judge extraction against your own taste and adjust grind in small steps.

Safety

The supplied evidence contains no specific safety guidance for grinding or brewing. Follow the instructions supplied with your grinder or brewing equipment, particularly for electric blade and burr grinders.

Related articles