Record coffee dose, water and timer events with an Acaia Pearl
How to use the original Acaia Pearl's tare, timer and brewing modes to separately log equipment weight, dry coffee dose, water added, beverage weight and brew time.
Contents
- The four quantities to keep separate
- Set up the scale before you weigh anything
- Step 1: Record the dry dose first
- Step 2: Choose a timer workflow
- Dual Display: manual control of time and weight
- Timer Starts with Flow: let the first pour start the clock
- Beverage mode: log water added and beverage yield
- Immersion brewers and equipment you take off the scale
- A brew log template
- Common logging mistakes
The original Acaia Pearl can log a full brew if each number has a clear meaning. Weigh and write down the dry dose before you tare for brewing. Then pick one timer workflow: manual timing in Dual Display, automatic timing in Timer Starts with Flow, or Beverage mode, which tracks cup, dripper and coffee separately and later shows both water and beverage readings. Every time you press Tare, the display starts measuring from a new zero point. Your log should record each zero point so you never mix up equipment weight, coffee, water and finished beverage.
This guide follows Acaia's English manual for the original Pearl (models AP001AT and AP004AT on firmware 2.0.010). Acaia publishes separate manuals for different firmware versions and recommends checking your firmware with its updater app first. If your firmware is different, button presses and mode names may not match what is described here.
The four quantities to keep separate
| Quantity | What it represents | How to capture it on the Pearl |
| Equipment weight | Containers, brewer, filter, cup or mug | Write down the reading before you tare it away, or let Beverage mode register each item |
| Dry dose | Ground or whole coffee only | Tare the empty dosing container, add coffee, write down the reading before any later tare |
| Water added | Water poured onto the coffee | Tare the full brewing setup (equipment and coffee), then read the display as you pour |
| Beverage weight | Liquid that ends up in the cup or server | In Beverage mode, take the reading marked 'b' after the dripper and filter come off |
The common mistake is reading a number without knowing what was zeroed before it. Say you tare a mug with a brewer and grounds on it, then pour. The display shows water added. It does not show the coffee or the finished beverage. Note what was on the scale at each tare and the numbers stay useful.
Set up the scale before you weigh anything
- Put the Pearl on a stable surface with no vibration, and keep it as level as you can.
- Center the container or brewer on the platform.
- Capacity is 2000 g. Taring resets the display, but it does not create more capacity. Everything on the platform counts toward the limit, including items you have tared away.
- The scale shows grams or ounces. Pick one unit and note it in your log so you don't mix units between brews.
- Acaia suggests a heat pad or pour-over stand under hot brewers and servers to reduce heat reaching the scale. Use the Pearl at room temperatures between 15 and 40°C (about 59 to 104°F).
- The Pearl is not waterproof. Do not submerge it, and wipe up spills rather than rinsing the scale.
Step 1: Record the dry dose first
Weigh the coffee in its own container before anything else. A tap on Tare zeroes whatever is currently on the scale. If you dose straight into the brewer and tare again before writing the number down, the dose is lost. Weighing Only mode works well for this step. In that mode, the manual says to hold Tare to switch between grams and ounces, and to hold Power to change modes.
- Place the empty dosing container on the scale. If you want its weight for your records, write down the reading.
- Tap Tare so the display reads zero.
- Add coffee until you reach the dose you want.
- Write down the reading as your dry dose before you tare again for anything else.
Illustrative example with made-up numbers: an empty container reads 142 g, and the container with coffee reads 160 g, so the dose is 18 g. You get the same 18 g if you tare the empty container first and read the display after adding coffee. Any water reading you take later is measured from the new zero you set for brewing. It is not measured from this container.
Step 2: Choose a timer workflow
| Mode | How the timer behaves | Best fit for logging |
| Dual Display | Press Power to start, stop and reset the timer. Weight display rolls over above 1000 g, and the timer stops at 9:59 | Brews where you want to control exactly when timing starts |
| Timer Starts with Flow | Press Power to tare and arm flow detection. Pouring starts the timer, and lifting the equipment off stops it | Pour-overs where the first pour should mark time zero |
| Beverage mode | Registers cup, dripper/filter and coffee in separate steps. The first detected flow starts the timer. After the filter comes off, the display alternates between water and beverage readings | Brews where you want both water added and beverage yield |
| Espresso, Weighing Only, Portafilter | Other modes listed in the manual | Weighing Only is useful for dosing. Check your manual for details of the espresso modes |
Dual Display: manual control of time and weight
- Place the full brewing setup on the scale, with brewer, filter, coffee and the vessel underneath. Write down the gross reading if you want it.
- Tap Tare. From now on, the display shows only what you add.
- Press Power to start the timer at the moment you decide counts as the start, such as the first pour.
- Write down water readings at whatever points you track, such as the end of each pour.
- Press Power to stop the timer and write down the elapsed time, then press it again to reset.
- Keep in mind that the weight display rolls over above 1000 g, and the timer stops at 9:59. For larger or longer brews, use a different mode or make a note of when a rollover happened.
Timer Starts with Flow: let the first pour start the clock
- Place the full brewing setup on the scale.
- Press Power. This tares the scale and turns on flow detection.
- Start pouring. The timer begins on its own when the scale detects flow, so time zero is the moment water first hits.
- Write down the water reading at the points you track.
- Lift the equipment off the scale to stop the timer, then write down the final time. Note in your log that removing the equipment is what stopped it.
Beverage mode: log water added and beverage yield
Beverage mode is the only documented workflow that gives you both water added and the weight of the finished drink. The scale moves through registration steps for the cup, the dripper with filter, and the coffee. It moves to the next step once the reading is stable, or when you tap Tare.
- Place the cup or server on the scale and let the scale register it.
- Add the dripper and filter, and let the scale register them.
- Add the coffee, and let the scale register the dose. You can compare this with the dose you weighed separately.
- Start pouring. The first detected flow starts the timer.
- When brewing is finished, lift the dripper and filter off.
- The display now alternates between the water reading and the beverage reading. The beverage reading is marked with a 'b'. Write down both numbers along with the elapsed time.
Immersion brewers and equipment you take off the scale
Immersion brewers need the same care about zero points. In an AeroPress method shown by Bean & Bean, the assembled brewer, grounds and mug are zeroed together before water is added, so the reading shows water only. Everything is then lifted off the scale before plunging. If you use a method like this, record the water reading before anything leaves the scale. Also note the removal as an event, because the scale can't show anything useful about the plunge itself.
A brew log template
Here is a log you can copy into a notebook or spreadsheet. The dose and water fields are separate so a later tare cannot overwrite either one.
Date / coffee:
Scale model / firmware / manual version:
Mode: Unit (g or oz):
DOSE
Dosing container (optional):
Dry dose:
BREW SETUP
Items on scale at brewing tare:
Gross load before tare (optional):
Timer trigger (Power press / first flow):
EVENTS
Time | Reading | What the reading represents | Note
0:00 | | water added | first pour
| | |
Equipment removed at:
Mode changes:
RESULTS
Total water added:
Beverage weight ('b' reading, Beverage mode only):
Elapsed time:
Tasting notes:
Common logging mistakes
- Taring before you write down the dose. The dose is gone once the display goes back to zero.
- Recording water added as beverage weight. Some water stays in the grounds and filter, so the two numbers measure different things. Only Beverage mode gives you the 'b' reading.
- Forgetting the gross load. The 2000 g capacity includes everything you tared away, so a heavy server plus brewer can use up most of it.
- Not writing down the timer trigger. A time started by hand on a Power press can't be directly compared with one started by first flow.
- Treating a rolled-over Dual Display reading above 1000 g as the actual total.
Related articles
What Does the 80/20 Rule Mean for Coffee?
Discover how the 80/20 rule applies to coffee brewing. Learn about the 80/20 ratio, how small adjustments affect flavor, and how to find your perfect cup through simple experiments.
Record coffee particle-size distributions using Gagné’s image procedure
A step-by-step guide to photographing ground coffee, calibrating the image, detecting particles and recording a particle-size distribution with Gagné’s method, kept separate from sieve fractions and grinder settings.
Keep a Home Coffee Blend Journal with Measured Proportions
Learn how to record home coffee blends by weight, calculate blend percentages, keep them separate from your coffee-to-water ratio, and compare trials.
Calculate Home-Brewed Coffee Ingredient Cost per Serving
Work out what each cup of home-brewed coffee costs in ingredients, using your own prices, a printable worksheet, spreadsheet formulas and a savings comparison.
Calculate coffee TDS and extraction yield and read the SCAA drip-brewing chart
How TDS, beverage-based extraction yield, brew ratio and taste differ, how to calculate extraction from refractometer readings, and how to read the 2016 SCAA drip-brewing chart.
Iced pour-over coffee: recording hot water, ice and dilution
How to plan and log an iced pour-over: separate entries for coffee dose, hot extraction water, brewing ice, measured beverage and later serving ice or water, with one worked recipe example.
Recording brewing water: labels, minerals and measurements
How to document the water behind each home coffee brew: source, label minerals, treatment and real measurements, kept separate from brewed-coffee TDS and tasting notes.
Coffee scoops, tablespoons and grams: recording measurements
How to turn coffee scoops and tablespoons into grams, weigh and record your own scoop, convert common doses, and use a simple coffee-to-water ratio at home.
What Is a Bloom Ratio? How the Coffee Bloom Works and What the Evidence Supports
What a bloom ratio means in pour-over coffee, how the bloom differs from your total brew ratio, and the steps and timing the sources support, with clear notes where details are missing.
Coffee Grind Size Chart: Matching Grind to Brewing Method and Extraction
A practical coffee grind size chart from finest to coarsest, how grinding methods differ, and how to adjust grind to your brewing method. Unverified details are flagged.