THE PERSONAL BREW BENCH

Recording brewing water: labels, minerals and measurements

How to document the water behind each home coffee brew: source, label minerals, treatment and real measurements, kept separate from brewed-coffee TDS and tasting notes.

5 min readThe ratio desk7 viewsRecording brewing water: labels, minerals and measurements
— · 0 votes
Contents
  1. The short answer
  2. Why a separate water record matters
  3. What to record for each water
  4. "Not supplied" is not zero
  5. Keep label values and home measurements in different columns
  6. Recording actual measurements
  7. Water TDS versus brewed-coffee TDS
  8. Check units and methods before comparing
  9. Equipment water requirements
  10. Example record (illustrative)
  11. Comparing two waters at home

The short answer

Give every water you brew with its own ID. Under that ID, record where the water came from, what its label or water report lists (with the exact units printed), any treatment it went through, and any measurements you actually took, including the instrument and date. Keep three kinds of information in separate places: what a label or report claims, what you measured at home, and what you tasted. A product description, a mineral target you read about, or a tasting impression is not a measurement and should never fill a measurement field.

Why a separate water record matters

Home brewers often change water in stages, and each stage is a different variable. For example, the author of a coffee-water article published by the roaster Newbery Street describes moving from tap water to purchased reverse-osmosis (RO) water, then trying mineral products and later home filtration. The taste improvements they report are their own experience. They do not establish mineral targets or show how any product performs. The account does show why each switch deserves its own entry. Without separate records, you cannot tell later which water produced which cup.

What to record for each water

  • Water ID: a short unique code, such as W01 or W02, that you write on every brew log entry.
  • Source: municipal tap, a named bottled water, purchased RO water, filtered tap, or a home-mixed water.
  • Date: the collection date for tap or filtered water, or the bottle or purchase date for packaged water.
  • Label or report issuer and date: who published the mineral information (the bottler, the water utility, or a lab) and the date shown on it.
  • Listed substances with exact units: copy each value and unit exactly as printed. Do not convert or round unless you note that you did.
  • Treatment device and cartridge: the filter, pitcher, or RO unit, plus the cartridge or membrane identity and when it was installed.
  • Treatment sequence: the order of steps, such as tap, then carbon filter, then RO, then a mineral addition.
  • Brew IDs: every brew made with this water.

"Not supplied" is not zero

If a label does not list a mineral, write "not supplied." Do not write 0. A measured zero is a result. A missing value is an absence of information. Treating them the same will mislead you when you compare waters later.

Keep label values and home measurements in different columns

A bottle label and a home meter reading describe different things, taken at different times by different methods. Put them side by side in separate columns rather than averaging them or overwriting one with the other. If they disagree, record both values as they are.

Recording actual measurements

Each measurement you take gets its own row with these fields: the property measured, the instrument and model, the method or instruction you followed, the date, the displayed value, and the unit shown. Record the value as the instrument displays it. If you only have a label value, leave the measurement fields empty.

Water TDS versus brewed-coffee TDS

TDS (total dissolved solids) can describe two very different samples in coffee. Brewing-water TDS describes the water before it touches coffee. Brewed-coffee TDS describes the finished beverage, which mostly reflects what was extracted from the grounds. Use separate sample rows labeled "brewing water" and "brewed coffee," and never copy a water reading into the beverage field or the reverse. Also note which instrument produced each reading, because a meter set up for one kind of sample is not automatically suited to the other.

Check units and methods before comparing

Two numbers are comparable only if their units and methods match. Before you compare a label value with a reading, or one reading with another, confirm that the units are the same and that the readings came from the same type of measurement. When in doubt, record the mismatch rather than forcing a comparison.

Equipment water requirements

Some brewers and espresso machines come with manufacturer guidance on water. Attach the specific requirement for your machine, taken from its manual or the manufacturer's documentation, to your water record before deciding whether to use a particular water in it. A general article, a water product's marketing, or another person's setup does not tell you what your machine accepts.

Example record (illustrative)

The layout below is a hypothetical template. The blank and placeholder entries show where information goes. They are not real values.

WATER ID: W02
Source:            purchased RO water, then mineral addition
Bottle/collect:    [date]
Label/report:      [issuer], dated [date]
Treatment:         [device / product name], step order: RO -> addition
Brews:             B014, B015, B016

SUBSTANCE     LABEL VALUE (unit as printed)   HOME MEASUREMENT
Calcium       not supplied                     -
Magnesium     [value] [unit]                   -
Bicarbonate   [value] [unit]                   -

MEASUREMENTS
Sample          Property  Instrument/model  Method ref  Date    Value  Unit
brewing water   TDS       [meter, model]    [manual]    [date]  [ ]    [ ]
brewed coffee   TDS       [meter, model]    [manual]    [date]  [ ]    [ ]

Equipment requirement attached: [brewer manual section]

Comparing two waters at home

  • Give water A and water B separate IDs.
  • Brew both with the same coffee recipe you have already chosen.
  • Record every deviation from that recipe in each brew's log entry.
  • Link each tasting note to its brew ID, and through the brew ID to its water ID.
  • Use your preference to choose the next trial.

A preference for one water is a useful observation, but it does not tell you a mineral concentration or prove which component caused the difference. Keep the tasting note in the tasting column and let it guide your next trial, not your measurement records.

Related articles