Calculate coffee TDS and extraction yield and read the SCAA drip-brewing chart
How TDS, beverage-based extraction yield, brew ratio and taste differ, how to calculate extraction from refractometer readings, and how to read the 2016 SCAA drip-brewing chart.
Contents
The short answer
TDS (total dissolved solids) is how concentrated your coffee is. It is the percentage of the drink, by mass, that is dissolved coffee. Extraction yield (EY) is how much of your dry coffee dose ended up dissolved in the drink. You do not calculate TDS yourself. A refractometer measures the liquid's refractive index and converts it to TDS%. You then calculate beverage-based extraction yield from that reading.
Dissolved coffee (g) = beverage mass (g) × TDS% ÷ 100
Extraction yield (%) = 100 × dissolved coffee (g) ÷ dry dose (g)
Shortcut: EY% = beverage mass × TDS% ÷ dry dose
The SCAA drip-brewing chart plots strength (TDS) against extraction. Its diagonal lines, however, are drawn from the ratio of coffee to input water, not from the weight of the brew you collected. Keep four things in separate places: concentration, beverage-based extraction, input ratio and how the cup tasted.
Four terms that get mixed up
| Term | What it describes | How you get it |
| TDS / strength / solubles concentration | Percentage of the liquid that is dissolved coffee | Measured with a refractometer on a sample of a specific liquid |
| Extraction yield / solubles yield | Percentage of the dry dose that dissolved into the drink | Calculated from TDS, beverage mass and dry dose |
| Input ratio | Water poured in relative to dry coffee, e.g. 14:1, or grams of coffee per liter of water | Weighed before brewing |
| Sensory observation | Sweetness, bitterness, body, clarity, and so on | Tasting notes; never a substitute for a measured number |
Input water and collected beverage are different numbers because the grounds hold back some water. Beverage-based extraction uses the weight of the liquid you actually collected. If you put input water into that formula instead, the result will be wrong.
Worked examples of beverage-based extraction
Example published by coffee writer Mikami: a 10 g dose brewed with 140 g of water gives an input ratio of 14. That brew yielded 121 g of beverage at 1.6% TDS. Extraction yield = 121 × 1.6 ÷ 10 = 19.36%. TDS is entered as the percentage number (1.6), not as 0.016. If you use the decimal form, multiply by 100 at the end.
Illustrative example, constructed for this guide: assume a baseline-corrected reading of 1.20% TDS, 270 g of collected beverage and an 18 g dose. Dissolved coffee = 270 × 0.012 = 3.24 g. Extraction yield = 100 × 3.24 ÷ 18 = 18%. This calculation covers only the collected beverage. Do not quietly reuse it as a total-extraction figure for an immersion brew.
Mikami has also described serving coffee at around 14% EY and under 1.2% TDS. That is one person's attributed preference, not a target everyone should aim for. It shows why the numbers describe a cup without ruling on whether you will like it.
Getting a usable TDS reading
The extraction figure can only be as good as the TDS reading. The guidance for the DiFluid R2 Extract (model DFT-R102) outlines this routine:
- Start with a clean sample dish.
- Zero the device with room-temperature pure water. Wait about five seconds, then give a short press followed by a held press until the display shows Zeroing.
- Dry the dish, add cooled coffee, and tap to measure.
- Leave at least three seconds between consecutive tests.
- Use the device within its stated operating range of 5–40°C, and keep the sample and the device at matching temperatures.
DiFluid describes two zeroing choices. You can zero with your brewing water, or with distilled water. If you zero with distilled water, measure your brewing water separately and subtract that baseline before you calculate extraction. Otherwise the minerals in your water get counted as coffee.
Reading the SCAA drip-brewing chart
The chart discussed here comes from the SCAA Technical Standards Committee's Guidelines for Using By-Pass in the Drip Coffee Brewing Process, revised 12 September 2016, Figures 1–3. Before you plot anything, identify what each part of the chart represents:
- Horizontal axis: extraction (solubles yield), running from 14% to 26%.
- Vertical axis: strength (solubles concentration), running from 0.80% to 1.60%.
- Diagonal formula lines: grams of coffee per liter of input water, labeled from 40 to 70 g/L.
- The region labeled Optimum Balance: a designation on the chart, not a guarantee that every coffee will taste best there.
The document's worked example uses 100 g of coffee to 2 L of water, or 50 g/L. Measured strength of 1.20% on that formula line plots at 21.5% extraction. The chart's extraction value comes from its own input-water convention. Simply multiplying 2,000 g of input water by 1.20% and dividing by 100 g would give 24%, not 21.5%. Neither number equals a beverage-based EY calculated from the measured weight of what you collected.
To use the chart: find your input ratio's formula line, then move along it to your measured strength, and read the extraction value below that point. Record the chart's issuer, its version and which convention produced the point. You can also plot your own beverage-based EY against strength. If you do, label that point separately so the two kinds of extraction figures never get mixed in your notes.
When the brew is diluted with bypass water
The 2016 guidelines were written for drip brewers that add bypass water, which is hot water routed around the coffee bed and blended in afterward. The concentrate coming off the bed is stronger than the finished, diluted coffee. The document therefore recalculates the formula lines for bypass setups. Always note which liquid you sampled, concentrate or finished blend, and how much bypass water was added. A concentrate reading plotted as though it were the finished cup will land in the wrong place.
A brew journal layout that keeps the numbers honest
An original worksheet layout for home brewing records. Each column holds one kind of information:
| Field | What to write |
| Method | Brewer and technique |
| Dry dose | Grams of coffee |
| Input water | Grams of water poured |
| Collected beverage | Grams of liquid you ended up with |
| Bypass amount | Grams added after brewing, if any |
| Sampling stage | Concentrate or finished drink |
| Instrument | Refractometer model, or none |
| Calibration baseline | Zeroing water and any subtracted baseline |
| Corrected TDS% | Reading after baseline correction |
| EY convention | Beverage-based, or chart/input-water based |
| Chart issuer and version | e.g. SCAA, revised 12 September 2016 |
| Plotted coordinates | Strength and extraction as plotted |
| Tasting notes | Your sensory observations, kept separate |
Never fill in an extraction number from taste alone. If a cup tastes thin or harsh, write that in the tasting column. Measured TDS, a calculated EY and the cup you actually tasted are only useful together when each is recorded as what it is.
Related articles
What Does the 80/20 Rule Mean for Coffee?
Discover how the 80/20 rule applies to coffee brewing. Learn about the 80/20 ratio, how small adjustments affect flavor, and how to find your perfect cup through simple experiments.
Record coffee particle-size distributions using Gagné’s image procedure
A step-by-step guide to photographing ground coffee, calibrating the image, detecting particles and recording a particle-size distribution with Gagné’s method, kept separate from sieve fractions and grinder settings.
Keep a Home Coffee Blend Journal with Measured Proportions
Learn how to record home coffee blends by weight, calculate blend percentages, keep them separate from your coffee-to-water ratio, and compare trials.
Calculate Home-Brewed Coffee Ingredient Cost per Serving
Work out what each cup of home-brewed coffee costs in ingredients, using your own prices, a printable worksheet, spreadsheet formulas and a savings comparison.
Record coffee dose, water and timer events with an Acaia Pearl
How to use the original Acaia Pearl's tare, timer and brewing modes to separately log equipment weight, dry coffee dose, water added, beverage weight and brew time.
Iced pour-over coffee: recording hot water, ice and dilution
How to plan and log an iced pour-over: separate entries for coffee dose, hot extraction water, brewing ice, measured beverage and later serving ice or water, with one worked recipe example.
Recording brewing water: labels, minerals and measurements
How to document the water behind each home coffee brew: source, label minerals, treatment and real measurements, kept separate from brewed-coffee TDS and tasting notes.
Coffee scoops, tablespoons and grams: recording measurements
How to turn coffee scoops and tablespoons into grams, weigh and record your own scoop, convert common doses, and use a simple coffee-to-water ratio at home.
What Is a Bloom Ratio? How the Coffee Bloom Works and What the Evidence Supports
What a bloom ratio means in pour-over coffee, how the bloom differs from your total brew ratio, and the steps and timing the sources support, with clear notes where details are missing.
Coffee Grind Size Chart: Matching Grind to Brewing Method and Extraction
A practical coffee grind size chart from finest to coarsest, how grinding methods differ, and how to adjust grind to your brewing method. Unverified details are flagged.