Identify and record your espresso machine's preinfusion phase
How to find your espresso machine's documented preinfusion phase, copy its controls and units, and log observed phase events in a brew journal tied to each shot.
Contents
Preinfusion is the stage at the start of a shot when water reaches the coffee bed under a gentler, separately controlled condition before full brewing pressure arrives. How it works, what it is called and how it is set differ from machine to machine. To record it usefully, start from your machine's manual. Copy the phase label, its documented meaning and the controls and units it lists. Then log what you see during the shot in separate fields, and attach that row to the shot it belongs to.
What preinfusion means on your machine
Manufacturers deliver preinfusion in different ways. Two manuals show the range. On the Slayer Single Group, the coffee bed is wetted with flow controlled by a needle valve. On the Speedster, the coffee bed can be wetted with water at supply-line pressure while the pump is off, or through a spring-and-piston cylinder that applies pump pressure progressively. Both count as preinfusion, but the controls, cues and settings are not interchangeable. A setting copied from a forum or Reddit thread only means something if it comes from the same machine, in the same mode, using the same event definitions. Before you compare your numbers with anyone else's, confirm all three.
Find the definition you will record against
Use the manual edition that matches your machine and note its version or revision date and page numbers. Look for four things:
- The exact name the manufacturer gives the phase, such as Pre-Brew or pre-infusion.
- The control that governs it: lever or actuator position, timer menu, or valve.
- The unit and range of any setting, and how the machine confirms that a setting has been saved.
- Any cue the manual gives for when the phase should end.
Example: Slayer Single Group (manual V6.4, June 7, 2021)
The actuator has three positions. Off is at the right, Pre-Brew is in the center and Full-Brew is at the left (printed pp.20–21). In Slayer's own Slayer Shot method, flow controlled by the needle valve wets the bed during Pre-Brew. The documented cue to move left to Full-Brew is crema appearing evenly across the underside of the basket. This manufacturer cue is a different event from the first appearance of liquid, so record the two separately.
The Pre-Brew timer in the menu changes in one-second steps up to 30 seconds, and a setting of zero turns it off. Pressing the round touch sensor confirms the setting. Moving the actuator does not (printed p.24). With the timer on, moving the actuator straight to Full-Brew starts an automatic pre-brew and full-brew sequence. Note in your record whether you used this automatic sequence or controlled the phase by hand. The manual measures needle-valve flow separately, as grams of water collected per 30 seconds (printed p.22). Keep that measurement in its own field, not mixed in with the timer value.
Example: Speedster (manual revised June 28, 2017)
The lever has three positions (printed pp.11–12):
• Upper: closes the group valve and stops the pump.
• Middle: opens the valve with the pump off, letting in water at supply-line pressure for manual pre-infusion.
• Lower: opens the valve and starts the pump.
If you move the lever straight from upper to lower, a spring-and-piston progressive pre-infusion cylinder still comes into play. Once the piston reaches the end of its travel, full pump pressure is applied progressively. You can see the piston rod sticking out, which gives you a visible event to record. The Speedster's shot timer counts the whole time the group valve is open, whether or not the pump is running, so its total includes the preinfusion time.
| Item | Slayer Single Group | Speedster |
| Phase control | Actuator in center Pre-Brew position; needle valve sets flow | Lever in middle position (pump off, line pressure) or progressive cylinder |
| Setting and unit | Pre-Brew timer, 1-second steps up to 30 s; 0 turns it off | Lever position; no timer value for the phase |
| Automatic option | Timer on plus a direct move to Full-Brew | Direct move from upper to lower engages the progressive cylinder |
| Transition cue to record | Crema even across basket underside (Slayer Shot method) | Piston rod reaches end of travel |
| Timer note | Pre-Brew timer is separate from the flow measurement | Shot timer counts all valve-open time |
What to put in a preinfusion record
Give the phase its own row, linked to the main shot entry. Keep the manual's wording in separate fields from your own descriptions of what you saw.
PREINFUSION PHASE RECORD
Parent shot ID: ____
Machine / model / version: ____
Manual edition and page: ____
Phase label (as printed): ____
Documented meaning: ____
Control used: ____
Setting entered + unit: ____
Mode (manual / automatic): ____
Observed start event: ____
Observed transition event: ____
Beverage appearance: ____
Illustrative example, not a real measurement: Field A is the timer value as shown on the machine's display. Field B is when liquid first appears. Field C is when you saw the phase change, such as the Slayer crema cue or the Speedster piston rod reaching the end of its travel. B and C often happen at different moments, so give each one its own entry. A programmed interval and an observed wetting event are not the same thing, and keeping them apart is what makes your records comparable.
A repeatable recording workflow
- 1. Find the manual that applies to your machine and write down its definition of the phase, with edition and page.
- 2. Copy only the controls and units that manual documents, and note how the machine confirms a setting.
- 3. Choose manual or automatic mode before you pull the shot, and log it.
- 4. During the shot, note the start event, the first liquid and the transition event in separate fields.
- 5. Attach the phase row to its parent shot, along with your timer start and end conventions. If you record full pressure or flow curves, store them with that shot as well.
- 6. When comparing shots, compare only records made in the same mode with the same event definitions.
Related articles
Record a Bruer cold-drip brew from setup to beverage yield
A practical log for a Bruer cold-drip session: method check, Bruer's setup quantities, drip-rate counting, timing events, collected beverage and cleanup notes.
Organize Existing Coffee Equipment Around Your Brewing Workflow
Set up a DIY home coffee station using only what you own: map your brewing sequence, group tools by use, check placement, and record a repeatable routine.
Keep a personal tasting record as one coffee brew cools
A practical guide to recording successive tasting notes from a single coffee brew as it cools, using elapsed time, measured temperatures and clear comparisons.
Interpret and record espresso pressure readings in context
Looking for the optimal bar pressure for espresso? Learn what your gauge actually measures, how to tell a setting from a reading, and how to log pressure so your numbers can be compared.
Record espresso basket dimensions, dose ratings and headspace
58mm espresso baskets share a diameter but differ in depth and dose range. How to record basket specs, actual doses and headspace checks without guessing at fit.
Record espresso pressure and flow profiles as separate observations
Build a stage-by-stage espresso profile record that keeps intended settings, measured pressure, measured flow and inferred curve segments apart.
Record a Nel Drip Recipe, Pouring Sequence and Beverage Yield
Build a cloth-filter brewing journal that keeps the author's nel drip method intact, logs each pour and pause as it happens, and records beverage yield as its own measurement.
Build a model-specific percolator brewing journal
Record your percolator's model, instructions, heat source, brewing events and completion cues so you can repeat a stovetop or electric routine and compare recipes fairly.
Document espresso spraying and uneven flow before changing preparation
Build a repeatable espresso observation record that separates what you saw, like spraying or uneven flow, from what you suspect caused it and what you change next.
Compare espresso adjustments with a controlled shot journal
Use a controlled shot journal to test espresso adjustments one variable at a time, alongside taste guides like the Barista Hustle Espresso Compass.