THE PERSONAL BREW BENCH

Record a Bruer cold-drip brew from setup to beverage yield

A practical log for a Bruer cold-drip session: method check, Bruer's setup quantities, drip-rate counting, timing events, collected beverage and cleanup notes.

5 min readBrew journal10 viewsRecord a Bruer cold-drip brew from setup to beverage yield
— · 0 votes
Contents
  1. Confirm the method before you log it
  2. Bruer's setup steps and quantities
  3. Setup worksheet: specified versus actual
  4. Measure and log the drip rate
  5. Record timing events as they happen
  6. Measure the collected beverage
  7. Close the session: taste, clean and plan one change

Recording a Bruer brew means writing down what Bruer's guide specifies, what you actually used, and what you observed during the drip. Log the brewer model, coffee dose and grind, prewet water, the ice and water mixture in the reservoir, the valve setting and drip rate you counted, each timing event, and the beverage you measured in the carafe. Keep the manufacturer's recipe values in one column and your real inputs in another. This lets you repeat a session you liked or change one thing at a time when you didn't.

Confirm the method before you log it

Name the extraction method first so your record compares like with like. The method depends on the water temperature during extraction and on how the water meets the grounds. Serving temperature does not decide it. A Bruer is a cold-drip tower, with separate zones for the water supply, the coffee chamber and the collected beverage. Cold water passes gradually through the grounds into the carafe below.

MethodExtraction waterHow water meets the groundsLog it as
Cold drip (Bruer)Cold water and iceDrips through the grounds into a collectorCold percolation
Immersion cold brewCold waterGrounds steep in the waterImmersion
Automatic or regular dripHot waterFlows through the groundsHot extraction, even if served over ice
Iced pour-over (for example, a Hario V60-style dripper)Hot waterPoured through the grounds onto iceHot extraction onto ice

Record machine automation and serving temperature in their own fields. A coffee served cold was not necessarily extracted cold, and an automatic machine can still be a hot-drip brewer.

Bruer's setup steps and quantities

Bruer's brewing guide gives the following sequence. Follow the instructions for your specific Bruer system when assembling it. These quantities belong to Bruer's recipe and should not be carried over to other towers.

  • Fit the mesh filter fine side up and insert the glass tower.
  • Add 60 g of medium-ground coffee and level the bed.
  • Seat the tower in the carafe, then place a paper filter on top of the grounds.
  • Prewet the grounds with about 2 fl oz of water.
  • Wet the lip of the seal and carefully insert the plug.
  • Fill the reservoir with 24 fl oz of ice and water, roughly half of each.
  • Set the valve. Aligning the etched line on the valve tube with the slot in the silicone opens it fully. Turning clockwise reduces the flow.
  • Adjust toward Bruer's recommended rate of one drip per second.

Bruer's FAQ also recommends a mixture where ice is still present throughout the brew. That makes ice observations worth logging during the session, as well as the starting mix.

Setup worksheet: specified versus actual

Fill in one row per field before opening the valve. Write "not measured" rather than guessing.

FieldBruer guide valueActual (with unit)
Session ID—
Brewer make and modelBruer (for example, BRUER-BLACK, formerly called Charcoal)
Guide followedBruer brewing guide
Coffee identity (roaster, origin, roast date)—
Dry dose60 g
GrindMediumGrinder and setting:
FiltersMesh (fine side up) plus paper on grounds
Water source—
Prewet waterAbout 2 fl oz
Reservoir mix24 fl oz, about half ice and half waterIce: / Water:
Target drip rate1 drip per second

Measure and log the drip rate

Count drops over a fixed interval and convert the count to drops per minute. Use the formula: drops counted ÷ seconds observed × 60. Bruer's one drip per second works out to 60 drops per minute.

Illustrative example only: if you count 24 drops in 30 seconds, then 24 ÷ 30 × 60 = 48 drops per minute. That rate is slower than Bruer's target, so you might open the valve slightly and count again. The figure shows the arithmetic only. It is not a recommended rate, and a drop count does not convert to a water volume.

Record timing events as they happen

Decide what counts as the start before you begin, such as the moment you open the valve, and write that definition down. Then log every check and adjustment on its own line.

Clock timeElapsedEventDrops countedInterval (s)Valve changeVisible flowIce present?
0:00Start (define):
Rate check
Valve adjusted
Reservoir empty
Last drip observed
Collection finished

Keep "reservoir empty," "last drip observed" and "collection finished" as separate events. These can happen at different times, and merging them makes sessions hard to compare. Record the actual elapsed time each session rather than assuming a fixed duration.

Measure the collected beverage

When collection ends, measure what is in the carafe and note the unit. Keep three amounts separate: the water and ice you put in, the beverage you collected, and any water, milk or ice you add afterward. The collected amount will not equal the input because the grounds retain some liquid.

Bruer describes the standard output as ready to drink rather than a concentrate, so don't label it concentrate by default. If you dilute it anyway, log the dilution as a separate step. For reference, Bruer lists the Black system's output as up to 590 ml (20 fl oz). That is a stated maximum, not the reservoir capacity or a guaranteed yield for any given session.

Close the session: taste, clean and plan one change

FieldEntry
Collected beverage (amount and unit)
Collection endpoint used
Dilution added afterward (amount and unit)
Taste notes
Cleaning completed
One change for next session

For cleanup, Bruer's cleaning guide says to discard the grounds and separate the metal filter from the silicone so trapped grounds rinse away. Bruer states that all parts of the system are dishwasher safe.

Coffeechecker recommends a habit for refining a cold-drip recipe: log grind, brewing time, water quantity and personal taste, then change only one variable before the next comparison. Applied to a Bruer, you might adjust the grind setting or the drip rate. Keep the dose and reservoir mix the same, and compare the two logged sessions side by side.

Related articles