Record and repeat a siphon coffee brew
Build a siphon coffee brew record you can repeat: choose one recipe, log each event with elapsed time, watch the key cues and change one variable at a time.
Contents
- What a siphon brew record is for
- Choose one recipe and keep it whole
- Set up the record before you heat anything
- Sequence for the Hario TCA manual example
- Sequence for the Hario UK recipe
- What to watch and how to judge the brew
- Safety points
- Illustrative example: a planned record before brewing
- Repeating and adjusting
What a siphon brew record is for
A siphon (or syphon) brew moves through distinct stages. Water heats in the lower bowl, rises into the upper bowl, steeps with the coffee, and then draws back down through the filter once the heat is removed. Each stage gives you a clear moment to note, so the method suits a written record. A good record captures the recipe, the equipment and the elapsed time of every event. With that, you can brew the same cup again or change exactly one thing and know what you changed. Use it when you want a repeatable home method rather than a different cup each morning, and when you compare doses, grind settings or timing across brews.
Choose one recipe and keep it whole
Start from a single identified recipe. Two published Hario approaches differ in quantities, in when the coffee goes in, and in timing. Keep each one intact. Mixing the dose from one with the sequence from the other gives you a record of neither.
| Element | Hario Technica (TCA) manual example | Hario UK home recipe |
| Coffee | About 10 g, medium grind, per cup | 24 g, medium grind |
| Water | 120 ml nearly boiling water per cup | 360 g |
| When coffee goes in | In the upper bowl before you seat it | After the water has risen into the upper bowl |
| Stirring | Mix lightly with a spoon handle once the water rises | Stir to wet the grounds, then stir briefly again after steeping |
| Time on heat after water rises | 40–60 seconds | 60-second steep |
| End of brew | Move the stand off the burner, extinguish the burner with its cover, let it draw down naturally | Remove from heat; drawdown takes 30–60 seconds |
The TCA instructions apply to that manual's brewer, not to every siphon. Before you adopt either recipe, read the instructions for your own brewer, filter and heat source. Where your equipment requires something different, follow your equipment and write the departure into the record.
Set up the record before you heat anything
Fill in the fixed details first. Then you only have to write times and observations during the brew. Neither recipe gives a numeric grinder setting or water temperature, so record your grinder and its setting exactly. That setting is what lets you reproduce "medium" on your own equipment.
- Date
- Recipe source (for example, the TCA manual or the Hario UK recipe)
- Brewer model and its marked capacity
- Which instruction version you are following
- Filter type and how you prepared it
- Heat source
- Coffee (name, roast or other identifying details)
- Dose in grams
- Water quantity, with its unit (ml or g)
- Grinder and grind setting
Below the fixed details, use three columns: event, elapsed time and observation. Log these events: heating start, upper-bowl seating, transfer (water has risen), coffee addition, each stir, the immersion interval, heat removal, and drawdown completion. Finish with the measured beverage yield and your own tasting notes. Decide once what each event means, for example that transfer is the moment the water has finished rising. Use the same definition every time so your records compare like with like.
SIPHON BREW RECORD
Date:
Recipe source:
Brewer model / marked capacity:
Instruction version:
Filter / preparation:
Heat source:
Coffee:
Dose (g):
Water (unit):
Grinder / setting:
EVENT | ELAPSED | OBSERVATION
Heating start | 0:00 |
Upper bowl seated | |
Transfer (water risen) | |
Coffee added | |
Stir 1 | |
Stir 2 | |
Heat removed | |
Drawdown complete | |
Beverage yield (measured):
Tasting notes:
Departure from recipe (if any):
One change for next brew:
Sequence for the Hario TCA manual example
- Before first use, prepare the cloth filter in boiling water.
- Center the filter in the upper bowl and secure its chain hook at the end of the tube.
- Measure about 10 g of medium-ground coffee and 120 ml of water per cup. Start heating the lower bowl with the heat source specified for the syphon, and log heating start.
- Put the coffee in the upper bowl before you seat it.
- Wait until boiling begins and the bubbling calms, then attach the upper bowl. Log the seating time.
- When the water rises, mix lightly with the handle of a spoon. Log transfer and the stir.
- Keep heating for 40–60 seconds. Pick a figure in that range and record it, so the next brew can match it.
- Move the stand away from the burner and extinguish the burner with its cover. Log heat removal.
- Let the coffee draw down naturally into the lower bowl, and log when it completes.
- Gently rock the upper bowl free and place it on its rest.
Sequence for the Hario UK recipe
- Measure 24 g of medium-ground coffee and 360 g of water.
- Heat the water and log heating start.
- Once the water has risen into the upper bowl, add the coffee and stir until the grounds are wet. Log transfer, coffee addition and the first stir.
- Steep for 60 seconds.
- Stir briefly again, then remove the heat. Log both.
- Expect the drawdown to take 30–60 seconds. Log when it completes.
What to watch and how to judge the brew
- Bubbling calming after the boil begins: in the TCA sequence, this is your signal to seat the upper bowl.
- Water rising into the upper bowl: this marks transfer. In the UK recipe it also tells you when to add the coffee. Start your immersion timing here.
- Drawdown: after heat removal, the coffee returns to the lower bowl. The UK recipe gives 30–60 seconds. Note whether yours falls inside that range and whether it took longer or shorter than last time.
- Beverage yield: measure what ends up in the lower bowl rather than assuming it matches the water you started with.
- Taste: write plain personal notes. These, together with the logged times, are how you judge one brew against the next.
Safety points
- Use the heat source specified for your syphon.
- Never move or refill a lit alcohol burner. In the TCA sequence you move the stand away from the burner, then extinguish the burner with its cover.
- Do not overheat the lower bowl once it is nearly empty. This matters after the water has risen, so keep to the timed heating interval and then remove the heat.
Illustrative example: a planned record before brewing
This is a hypothetical plan, not a completed brew. If you choose the TCA manual example, enter planned coffee as 10 g and water as 120 ml. Leave the actual measurements, transfer time, drawdown duration and beverage yield blank until you observe them. If you choose the UK recipe instead, replace the whole sequence and both quantities with that recipe's 24 g and 360 g.
Recipe source: Hario TCA manual example
Dose (g): planned 10 actual ____
Water (ml): planned 120 actual ____
Heat after rise: planned 40-60 s, chosen ____
Transfer time: ____
Drawdown duration: ____
Beverage yield: ____
Repeating and adjusting
To repeat a brew, copy the fixed details from your previous record and follow the same logged times. When you want a different cup, choose one deliberate change for the next record, such as the grind setting or a different point in the 40–60 second window. Write the change down before you brew, without predicting its effect. Keep everything else and every event definition the same. Then compare the new drawdown time, yield and tasting notes with the previous record.
Related articles
Record a Bruer cold-drip brew from setup to beverage yield
A practical log for a Bruer cold-drip session: method check, Bruer's setup quantities, drip-rate counting, timing events, collected beverage and cleanup notes.
Organize Existing Coffee Equipment Around Your Brewing Workflow
Set up a DIY home coffee station using only what you own: map your brewing sequence, group tools by use, check placement, and record a repeatable routine.
Keep a personal tasting record as one coffee brew cools
A practical guide to recording successive tasting notes from a single coffee brew as it cools, using elapsed time, measured temperatures and clear comparisons.
Identify and record your espresso machine's preinfusion phase
How to find your espresso machine's documented preinfusion phase, copy its controls and units, and log observed phase events in a brew journal tied to each shot.
Interpret and record espresso pressure readings in context
Looking for the optimal bar pressure for espresso? Learn what your gauge actually measures, how to tell a setting from a reading, and how to log pressure so your numbers can be compared.
Record espresso basket dimensions, dose ratings and headspace
58mm espresso baskets share a diameter but differ in depth and dose range. How to record basket specs, actual doses and headspace checks without guessing at fit.
Record a Nel Drip Recipe, Pouring Sequence and Beverage Yield
Build a cloth-filter brewing journal that keeps the author's nel drip method intact, logs each pour and pause as it happens, and records beverage yield as its own measurement.
Record espresso pressure and flow profiles as separate observations
Build a stage-by-stage espresso profile record that keeps intended settings, measured pressure, measured flow and inferred curve segments apart.
Build a model-specific percolator brewing journal
Record your percolator's model, instructions, heat source, brewing events and completion cues so you can repeat a stovetop or electric routine and compare recipes fairly.
Document espresso spraying and uneven flow before changing preparation
Build a repeatable espresso observation record that separates what you saw, like spraying or uneven flow, from what you suspect caused it and what you change next.