THE PERSONAL BREW BENCH

Record the 500 ml Clever Dripper's Water-First Brewing and Release Sequence

Follow the manufacturer's water-first recipe for the 500 ml Clever Coffee Dripper with a #4 filter, and log dose, water, grind, steep and drainage events for repeatable brews.

5 min readBrew journal7 viewsRecord the 500 ml Clever Dripper's Water-First Brewing and Release Sequence
— · 0 votes
Contents
  1. The short answer
  2. Check that your brewer matches the recipe
  3. Equipment and recipe baseline
  4. Step-by-step: the water-first sequence
  5. Timeline at a glance
  6. What to record in your brewing journal
  7. A copyable journal template
  8. Illustrative example: calculating elapsed times
  9. Using the journal to compare sessions
  10. A grounds-first alternative to keep separate

The short answer

The manufacturer's water-first recipe for the 500 ml Clever Coffee Dripper uses 18.5 g of coffee, 310 g of boiling water (100°C) and a standard #4 paper filter. All of the water goes into the brewer before the grounds. The timer starts when the grounds hit the water. The lid goes on by 0:25, and the coffee steeps until 1:10. At that point you stir and then set the brewer on a cup or carafe, which opens the drain valve. Drainage should be finished by about 2:30, and the recipe allows it to run as late as 2:45.

This guide sets out that sequence and gives you a simple journal format for it. If you record the same events each session, you can repeat a brew you liked or change one thing at a time on purpose.

Check that your brewer matches the recipe

The recipe is written for the Clever model the manufacturer lists with 500 ml practical capacity and a #4 filter. Confirm that your brewer and filters match before you use these numbers as your baseline. A different Clever size, a different filter or a grounds-first recipe should each get its own journal record so the results don't get mixed together.

The manufacturer's recipe does not give a grind setting. Write down the grinder and setting you actually use, because the other numbers in your journal can't be repeated without it.

Equipment and recipe baseline

ItemManufacturer water-first baseline
BrewerClever Dripper, 500 ml practical capacity
FilterStandard #4 paper filter, seams folded to fit
Coffee dose18.5 g
Brewing water310 g
Water temperatureBoiling, 100°C
Ratio (calculated)About 1:16.8 coffee to water
GrindNot specified; record your own grinder and setting
Other toolsScale, timer, stirring utensil, cup or carafe

Step-by-step: the water-first sequence

  • 1. Fold the seams of a #4 filter so it sits flat in the brewer.
  • 2. Rinse the filter with hot water and throw away the rinse water.
  • 3. Put the brewer on a scale and tare it.
  • 4. Pour in all 310 g of boiling water.
  • 5. Add the 18.5 g of grounds and start the timer the moment they enter the water.
  • 6. Stir to break up dry clumps and wet all the grounds.
  • 7. Put the lid on no later than 0:25.
  • 8. Let it steep until 1:10.
  • 9. Take the lid off. Stir the grounds off the filter walls with two full rotations.
  • 10. Set the brewer on a cup or carafe to open the drain valve.
  • 11. Stir four more times, then put the lid back on.
  • 12. At 2:30, lift the lid and check drainage. The recipe allows it to finish as late as 2:45.

Timeline at a glance

TimeEvent
0:00Grounds enter the water; start the timer
Right after 0:00Stir to break clumps and saturate the grounds
By 0:25Lid on
Until 1:10Steep
1:10Lid off; two full rotations to clear the filter walls
After the stirSet on a cup or carafe to open the valve; stir four more times; lid back on
2:30Lid off to check drainage
Up to 2:45Latest completion the recipe allows

What to record in your brewing journal

A useful journal entry has two parts. The first is the setup: what equipment and ingredients you used. The second is the timeline of events. Logging the actual time each event happened, rather than the time the recipe calls for, shows you where a session differed from your baseline.

  • Setup: brewer model and stated capacity, filter type, manufacturer reference and recipe version
  • Coffee: the coffee you used and the dose in grams
  • Water: water mass and temperature
  • Grind: grinder and the actual setting
  • Order: water-first or grounds-first
  • Output: mass of the collected beverage
  • Events: grounds enter water (00:00), saturation stir finished, lid fitted, lid removed, crust stir finished, valve opened, drainage finished
  • Notes: taste observations, written as you notice them

Calculate two durations separately from the event times. Contact-to-release runs from the grounds entering the water to the valve opening. Release-to-drain runs from the valve opening to the end of drainage. Keeping them apart helps you tell whether a change came from the steep or from the drawdown.

A copyable journal template

SESSION: ____    DATE: ____
Brewer / capacity:     Clever, 500 ml
Filter:                #4
Recipe reference:      Manufacturer water-first, version ____
Coffee:                ____
Dose (g):              ____
Water (g) / temp (C):  ____ / ____
Grinder / setting:     ____ / ____
Order:                 water-first
Beverage collected (g): ____

EVENT                          TIME
Grounds enter water            00:00
Saturation stir done           __:__
Lid fitted                     __:__
Lid removed                    __:__
Crust stir done                __:__
Valve activated                __:__
Drainage complete              __:__

Contact-to-release:            __:__
Release-to-drain:              __:__
Changed variable:              ____
Taste notes:                   ____

Illustrative example: calculating elapsed times

This is a made-up journal entry to show the arithmetic. It is not a recommended target. Say the grounds enter the water at 00:00, the valve opens at 01:18 and drainage finishes at 02:38. Contact-to-release is 1:18. Release-to-drain is 02:38 minus 01:18, which is 1:20.

Using the journal to compare sessions

Start from the manufacturer recipe as your baseline. When you want to compare, pick one recorded variable to change, such as the grind setting, and keep everything else the same. Write down what you taste and don't assume ahead of time how the change will turn out. Over several sessions, the setup details and the two durations let you see how each change relates to your taste notes.

A grounds-first alternative to keep separate

Roast! West Coast published a different, grounds-first Clever recipe. It uses 20 g of medium-fine coffee (about 1:15), 300 g of water and a rinsed #2 filter. It starts with a 45–60 g bloom for 20–30 seconds. You then add the rest of the water, stir and cover if you like, and steep for 2 to 2½ minutes, which the author describes as a personal preference. After that you release onto a vessel, and drawdown is expected to take 45–60 seconds. The source doesn't say which brewer size the recipe is written for, and it uses a different filter. If you try it, log it as its own recipe instead of comparing it directly with your 500 ml, #4, water-first sessions.

Related articles