Record grinder input, collected output and mass differences
Weigh beans before grinding and grounds after, log each pair in sequence, and read the input-output difference without mistaking it for total grind retention.
Contents
What a paired mass record accomplishes
Discussions of coffee retention, grind retention and zero-retention grinding often come down to one question: does the coffee that goes into the grinder come back out? A paired mass record helps you track that. You weigh the beans before each grind, weigh the grounds you collect afterward, and write down the difference. Over a sequence of grinds, this gives you a written history of what went in and what came out on your grinder, with your scale, under conditions you have noted.
This approach follows the single-dose workflow that a specialty coffee retailer describes for the Mahlkönig X64 SD: weigh the beans before grinding, then weigh the collected grounds. The record is useful when you single-dose for espresso or other brewing and want repeatable ratios. It is also useful when you keep personal tasting notes and want each cup tied to the actual mass that reached the basket or brewer.
Be clear about what the number means. Input minus output is a recorded input-output difference. It does not measure everything left inside the grinder, and it does not tell you which particles came out. If 18.0 g goes in and 18.0 g comes out, some of those grounds may have been left over from an earlier grind while some of the new coffee stayed behind. The record shows mass balance for each row, not an inventory of the grinder.
What you need
- The grinder you are recording, identified the same way in every row
- A scale, with its displayed increment noted (for example, whether it shows 0.1 g steps)
- A container for weighing beans and a container for collecting grounds, each tared before use
- A worksheet, either paper or a spreadsheet
- The grinder's own operating and cleaning instructions, for any step that involves running, purging or opening the machine
Set up the worksheet
Give each grind its own row and keep the rows in the order you actually ground. The order matters because each grind can be affected by the one before it. Use these columns:
Seq | Grinder | Setting | Cleaning state / preceding use | Scale + increment | Container tare | Input g | Output g | Input − output g | Spills / separately collected | Procedure used | Observations
The Observations column is where tasting notes go if you are linking flavor to dose. It is also where you note anything unusual, such as grounds clinging to the chute, a stalled grind, or a change of beans.
Steps, in order
- 1. Decide where the sequence starts and what counts as collected output before you weigh anything. For example, decide whether output means only what lands in the cup, or also anything you brush or purge out. Write the decision at the top of the sheet.
- 2. Record the grinder, the setting, and the cleaning state, including what was ground just before. If you don't know the preceding use, write that you don't know.
- 3. Note which scale you are using and its displayed increment. Tare the bean container and record the tare.
- 4. Weigh the beans and record the input mass.
- 5. Grind using the procedure in your grinder's instructions or the routine you documented. Write down which procedure you used. This worksheet does not prescribe grinder operation or cleaning steps.
- 6. Tare the collection container, collect the grounds within the boundary you set in step 1, and record the output mass.
- 7. If any grounds spilled or were collected separately, weigh them if you can and record them in their own column. Do not add them silently to the output.
- 8. Calculate input minus output for the row.
- 9. Repeat for the next grind in the next row. Keep conditions the same where you can.
When to change course
If anything changes partway through, note it in that row. Examples include a new grind setting, different beans, a cleaning, a different scale, or an added accessory such as a dose purger or bellows. Don't try to compare rows across that change as if conditions were the same. If the change is large, you can close the sequence and start a new one with fresh starting conditions. If you notice a recording error, correct it in a visible way and note the correction. Don't overwrite it.
Worked example (hypothetical numbers)
The figures below are made up to show the arithmetic. They are not measurements from any grinder.
| Seq | Input g | Output g | Input − output g |
| 1 | 18.0 | 17.6 | +0.4 |
| 2 | 18.0 | 18.2 | −0.2 |
| 3 | 18.0 | 18.0 | 0.0 |
| Total | 54.0 | 53.8 | +0.2 |
You can check the arithmetic: the row differences (+0.4, −0.2 and 0.0) should add up to the sequence difference (+0.2). The sequence difference should also equal total input minus total output (54.0 − 53.8).
How to read the result
- Positive difference: less coffee was collected than went in for that row, within the collection boundary you set.
- Zero difference: the collected mass matched the input. This does not show that the same coffee came out, or that nothing stayed inside the grinder.
- Negative difference: more was collected than went in for that row, as in row 2 above. Record it as it is. Do not assign a cause unless you have other evidence.
- Sequence total: the overall input-output difference across the run, under the conditions you noted.
The record is complete when every row has input, output and a difference. Spills and condition changes should be noted where they happened, and the row differences should add up to the sequence total. If you are using the record to address how retention might affect espresso flavor, put your tasting notes next to the masses. That way you can see whether particular rows, such as the first grind after a cleaning or after a setting change, line up with differences in the cup. The record shows that correlation. It does not establish a cause.
Comparing sequences
Before comparing two runs, for example before and after a change in your workflow, use the same start point, the same collection boundary and the same columns for both. Keep the other conditions as close as you can, and note every difference. Totals from sequences recorded under different boundaries or different scales cannot be compared directly. For instructions on running, purging, cleaning or opening the grinder, use the manufacturer's instructions for your model.
Read next
Record a Bruer cold-drip brew from setup to beverage yield
A practical log for a Bruer cold-drip session: method check, Bruer's setup quantities, drip-rate counting, timing events, collected beverage and cleanup notes.
Organize Existing Coffee Equipment Around Your Brewing Workflow
Set up a DIY home coffee station using only what you own: map your brewing sequence, group tools by use, check placement, and record a repeatable routine.
Keep a personal tasting record as one coffee brew cools
A practical guide to recording successive tasting notes from a single coffee brew as it cools, using elapsed time, measured temperatures and clear comparisons.
Identify and record your espresso machine's preinfusion phase
How to find your espresso machine's documented preinfusion phase, copy its controls and units, and log observed phase events in a brew journal tied to each shot.
Interpret and record espresso pressure readings in context
Looking for the optimal bar pressure for espresso? Learn what your gauge actually measures, how to tell a setting from a reading, and how to log pressure so your numbers can be compared.
Record espresso basket dimensions, dose ratings and headspace
58mm espresso baskets share a diameter but differ in depth and dose range. How to record basket specs, actual doses and headspace checks without guessing at fit.
Record espresso pressure and flow profiles as separate observations
Build a stage-by-stage espresso profile record that keeps intended settings, measured pressure, measured flow and inferred curve segments apart.
Record a Nel Drip Recipe, Pouring Sequence and Beverage Yield
Build a cloth-filter brewing journal that keeps the author's nel drip method intact, logs each pour and pause as it happens, and records beverage yield as its own measurement.
Build a model-specific percolator brewing journal
Record your percolator's model, instructions, heat source, brewing events and completion cues so you can repeat a stovetop or electric routine and compare recipes fairly.
Document espresso spraying and uneven flow before changing preparation
Build a repeatable espresso observation record that separates what you saw, like spraying or uneven flow, from what you suspect caused it and what you change next.